|
Makita LS1214FL 15 Amp 12-Inch Dual Bevel Compound Sliding Miter Saw with Laser and Fluorescent Light
12", Dual Slide Compound Saw With Laser & Fluorescent Light, Built In Laser With Micro Fine Adjustments Clearly Indicates Line Of Cut, Independent Switch Allows Laser To Be Seen Independently Of Blade Rotation, Built In High Output Fluorescent Light Illuminates Work Area & Lasts 2,000 Hours On Average, Dual Steel Rails Supported By Linear Ball Bearings Ensure Stable, Accurate Cutting, Powerful, Direct Drive 15A Motor Never Slips Or Bogs Down, 9 Positive Stops At 15 Degree, 22.5 Degree, 30 Degree, 45 Degree Left Or Right & 0 Degree For The Most Common Miter Cuts, Additional Positive Stops At 33.9 Degree Left For Model LS1214FL, Electronic Speed Control Maintains Constant Speed Under Load, Soft Start Feature For Controlled Operation, Single Cast Aluminum Base Has Built In Wrench Storage For Operator Convenience, Long Slide Track & Wide Pivot Angle Allow Cross Cuts Up To 4 x 12 Material, Large Turn Base & Adjustable Pivot Fence Supports Larger Stock.
What's not to love? This saw has everything, from indisputable Makita quality all the way up to all the coolest bells and whistles.
Makita LS1214FL 15 Amp 12-Inch Dual Bevel Compound Sliding Miter Saw with Laser and Fluorescent Light Accessories
 Delta 36-136 Universal Miter Saw Stand
Freud LU74R012 12-Inch 96 Tooth ATB Thin Kerf Cut-Off Saw Blade with 1-Inch Arbor and PermaShield Coating
DEWALT DW723 Miter Saw Stand
HTC PM7000 Portamate Miter Saw & Power Tool Work Center
Makita MAC2400 13 Amp 2-1/2 Horsepower 4.2-Gallon Oiled Twin Hot Dog Compressor
Bosch 1590EVSK 6.4 Amp Top Handle Jigsaw
StableMate PLUS100 Universal Miter Saw Stand
DEWALT DW7231 Miter Saw Workstation Tool Mounting Brackets
Forrest CM12806115 Chopmaster 12-Inch 80 Tooth ATB Miter Saw Blade with 1-Inch Arbor
Makita LCT300W 18V Compact Lithium-Ion 3PC Cordless Combo
Makita LS1214FL 15 Amp 12-Inch Dual Bevel Compound Sliding Miter Saw with Laser and Fluorescent Light Reviews
Ok I owen & opperate a Int.Trim Co. to the left or the right of each angle unless you lock the saw down each time.The other is that the guard catches the long point of a compound miter on any crown over 5 1/4" cut from the end of the material.So I am not sure if I am into this saw or not it has only been a month and I think I still like my Dewalt better.Time will tell.All and all it is a nice saw we do high end custom homes and spec.production homes thru out South Florida.Between myself & the guys we have used just about all the saws on the market and this one falls somewhere in the middle of the road.I have two issues with this saw the first being that the stops @ each miter have to much play about 1 Deg.
THis is a sweet saw until it broke. The parts had quality i would expect of an inferior tool manufacturer. Customer service was not concerned that their components did not stand up to regular use. The fence shattered in three different places within a few days of opening the box.
I have never owned this saw but I have used it quite a few times. I found it a little hard to move around and to adjust the settings. I has plenty of power.
This saw is amazing. Don't make a mistake and buy a Dewalt. the stock blade works extremely well when cutting crown molding. It makes precision cuts.
|
